Expert customer service in 9 languages. Plasma cutter - 100 A - 400 V. Cutting current: 30 - 100 A.
Cutting depth up to 35 mm. 2 T / 4 T switch.
Effective-modern IGBT inverter and pilot ignition. Powerful-maximum cutting current of 100 A, 100 % duty cycle at 63 A. Clear-control panel with LCD display and control dial can even be used with welding gloves. Precise-distortion-free separating cuts up to 35 mm material thickness even in meshes thanks to pilot ignition.Flexible-switch easily between 2-stroke and 4-stroke operation. Do you have a question? The cutting current of the plasma cutter S-PLASMA 100-IGBT from Stamos Germany can be set with a rotary control between 30 and 100 A, all values are clearly shown on the LCD display.
With a duty cycle of 100%, high 63 A are still possible. These performance values are sufficient to cut through workpieces up to 35 mm thick. Tool steels can be cut as well as stainless steel and other high-alloy steels, but also aluminum, copper and titanium. The burner is ignited via a pilot plasma arc, which can also be used to separate grids and grates. To prevent oxidation or deformation of the workpiece after a cut, the air supply continues by 10 s.
Use modern IGBT technology with the plasma cutter from Stamos Germany! Powerful plasma cutter with pilot ignition and 100 A. The plasma cutter S-PLASMA 100-IGBT from Stamos Germany with modern IGBT inverter technology cuts electroconductive materials such as steel, stainless steel, cast iron, copper, nickel and aluminium precisely and without distortion. The professional device enables you to make cuts up to max. 35 mm deep at a cutting output up to 100 A and is perfect for repair and renovation work in workshops or garages.Plasma cutter with high operating comfort. The cutting current can be adjusted between 30 and 100 A, and all values are clearly shown on the LCD display. At a duty cycle of 100 %, a high 63 A is still possible.
These performance values are sufficient to cut workpieces up to 35 mm thick. The plasma cutter can cut tool steels as well as stainless steel and other high-alloy steels. Even aluminium, copper and titanium can´t resist the powerful plasma arc of the S-PLASMA 100-IGBT. The plasma cutting machine offers two different working modes so that maximum progress can be achieved with every task.
In 2-stroke mode, the torch will run for as long as the power switch is pressed. In 4-stroke mode, a single tap is sufficient to activate the burner and another tap to switch it off. Th plasma cutter from stamos_germany works with three-phase alternating current at an operating voltage of 2 V. This makes it the perfect tool for automotive workshops, commercial metalworking operations and industrial production. In addition, it also supports DIY enthusiasts in their demanding renovation and repair projects.The torch is ignited via a pilot plasma arc, which can also be used to separate grids and grates. You can select the external compressor depending on the requirements and conditions and set the air pressure for plasma cutting via the external pressure reducer.
Thus, the device proves to be very flexible and easy to transport. To prevent oxidation or deformation on the workpiece after a cut, the air supply runs on for 10 seconds.The air run-on also cools the torch and prevents the risk of damage. The base unit is also equipped with powerful fan cooling to prevent overheating. If the operating temperature nevertheless rises excessively, the overheating protection comes into play. The compact steel housing protects the technical equipment inside the plasma cutting machine. From the outside, it is protected from environmental influences with a coating. The plasma cutter is easy to transport thanks to the practical handle. Allow yourself to be convinced by high quality and excellent service-order a plasma cutter from stamos_germany today! Duty cycle for 40°C [%]. Welding current at 100% duty cycle [A]. Welding current at 60% duty cycle [A].
0.00 x 0.00 x 0.00 cm. 54.95 x 28.00 x 39.00 cm. IGBT = insulated-gate bipolar transistor.
IGBT is a bipolar transistor with an insulated gate electrode. This semi-conducting device is being increasingly used in power electronics because it combines the advantages of two transistor types: the easy controls of the field effect transistor and the fast switching and high breakdown voltage of the bipolar transistor. The IGBT also offers some robustness against short circuits because it limits the electrical continuity. IGBTs are a further development of MOSFET technology.Powerful fans ensure an optimal removal of heat from the unit. For plasma cutting, a gas is required with which the molten metal is blown away from the work surface. Compressed air is a common solution for this. For this purpose, the plasma cutter has a compressor connection. This device works with a 3-phase connection (400 V +/- 10 %). The time after the weld is finished in which gas continues to flow from the torch; this cools the burner and protects the weld from oxidation.
Start the weld by placing pressure on the torch button. Stop the process by releasing the button. By pressing the torch button the solenoid valve opens. Allowing the gas to flow in.The gas pre-flow ignites the arc at the pre-set current. Releasing the burner button initiates a rise in the current to that of the pre-set welding current. The welding process stops once you press the burner button again. The plasma arc melts the metal and the kinetic energy of the compressed air blows the metal aside.
Choose between the 2T and 4T mode. Shows the welding / cutting parameters. The LED light indicates overheating or a malfunction. A pilot arc is ignited by pressing the torch´s trigger.Thus, grates can be cut. Plasma cutter S-PLASMA 100-IGBTPower cord without plug (4 m)Plasma torch with cable assembly (5 m)Pressure reducer2 clamping ringsAir hose (4 m)4 cutting nozzles4 electrodesInstruction manual. The Stamos Welding Group offers you a variety of different and modern welding devices at extremely low prices. No matter if plasma cutters, combined devices, MIG MAG, TIG or E-Hand welders - products by the Stamos Welding Group are made for daily continuous operation and live up to every expectation. The Stamos Welding Group lays much emphasis on development and improvement of the product range. We are proud to use exclusively the best materials in our machines.
Go for the brand products by the Stamos Welding Group and weld like professionals! This item is in the category "Business, Office & Industrial\CNC, Metalworking & Manufacturing\Welding & Soldering Equipment\Welding Equipment & Accessories\Welders, Cutters & Torches\Plasma Cutters".kingdom" and is located in this country: DE. This item can be shipped to United Kingdom.