SF-HC25G thc plasma cnc cutting machine automatic Arc cap voltage Plasma cutting

SF-HC25G thc plasma cnc cutting machine automatic Arc cap voltage Plasma cutting
SF-HC25G thc plasma cnc cutting machine automatic Arc cap voltage Plasma cutting
SF-HC25G thc plasma cnc cutting machine automatic Arc cap voltage Plasma cutting
SF-HC25G thc plasma cnc cutting machine automatic Arc cap voltage Plasma cutting
SF-HC25G thc plasma cnc cutting machine automatic Arc cap voltage Plasma cutting

SF-HC25G thc plasma cnc cutting machine automatic Arc cap voltage Plasma cutting
SF-HC25G thc plasma cnc cutting machine automatic Arc cap voltage Plasma cutting. SF-HC25G thc plasma cnc cutting machine automatic Arc cap voltage Plasma cutting machine cutter torch height controller. The SF-HC25G Plasma Torch Height Controller is a torch height automatic control module specifically designed for portable plasma cutting machines. The SF-HC25G plasma torch height controller is easy to operate, easy to debug, affordable, and fully digitally controlled for reliable performance.

It is an ideal accessory product for welding and cutting equipment manufacturers. The main unit and panel split structure make it ideal for portable cutting machines. There may be some differences between the physical and manual contents of the SF-HC25G plasma torch height controller. Please refer to the actual product. Be sure to read the safety warnings and precautions to avoid dangerous use due to improper use.

Before using this product, you must follow the detailed instructions in the system manual to ensure proper use of the product. Safety warnings are used to prevent injury to humans and property. The installer must be a relevant industry or a technician with relevant experience.

This manual must be read in detail before installation. Verify that the selected power supply matches the specifications you require. It is strictly forbidden to install or plug in and pull out the plug when the power is on. Install the location as far away as possible from the heat source. The controller enclosure must be well grounded to prevent electrical shock or to affect controller operation.

The steel to be cut must be well grounded and maintain a good connection to the controller casing to ensure the accuracy of the height control. Do not collide or vibrate strongly to avoid damage to the product. Do not disassemble the torch height controller or change its internal structure to prevent accidents or malfunctions.

This product adopts 32-bit arm as the core and two sets of 3-digit digital tube displays, which adopt digital control mode. The linear adjustment device is not included inside, which greatly improves stability. The speed parameters can be modified, and can be modified arbitrarily according to the power supply and lifting mechanism. The circuit adopts the chip technology, there is no adjustable device inside, and the full digital control technology ensures the high reliability of the product.

The operation is simple, and the two sets of digital tubes respectively display the set arc voltage and the actual arc voltage, which are simple and intuitive. There are 3 knobs for setting parameter operations. Simple and convenient interface, suitable for all plasma cutting CNC systems, can also be used alone. Adopt the proximity positioning mode of the proximity switch.

Pwm output, 255 speed adjustable, precise control of motor speed, multi-speed current setting, short circuit protection. The anti-collision function of the cutting tool, when the cutting nozzle touches the steel plate, the controller will quickly lift the cutting tool a certain distance to effectively protect the cutting nozzle. All input and output are opto-isolated, plasma voltage feedback adopts linear opto-isolation, independent isolated power supply, and can be very compatible with imported plasma power supply of each brand with its own voltage divider. Integrated arc start success judgment function, arc start success feedback function.

Power requirements: DC 24 V ± 10% 3 A / 50 Hz. Applicable motor: 24 V DC brush motor.

Initial positioning mode: proximity switch or mechanical switch (normally open normally closed through jumper cap setting). Maximum control accuracy: ±1 V.

Box size: host 145 X 90 X 42. Panel: 120 X 55 X 40. Working environment temperature: -10 60 ° C. Detection system: isolated arc voltage divider.

SF-HC25G arc voltage height controller has no special port. Four wires are required from the voltage divider of the SF-HC25G height adjuster and the plasma power connection. The two wires are at the port where the plasma starts to arc, and the plasma cutter will have it. The arc voltage signal is two lines divided into positive and negative poles.

If the plasma power supply does not have a dedicated port, the plasma power supply housing needs to be opened and connected from the secondary rectification inside the plasma power supply, which is the original arc voltage of the plasma power supply. You only need to connect the ground wire because the interference from the plasma power supply is too large. The ground wire needs to use a copper rod with a diameter of 50 mm or two angle steels with a length of 2 meters. Connect to the housing of the plasma power supply. There are many options, including China Post. We will try our best to help you! Dear buyers, if you are satisfied with our products, we can leave you 5-star feedback, we would be grateful.

We will provide you with some excellent solutions. We promise to help you solve it asap, and make you feel satisfactory absolutely.

Your recognition will make us more confident to develop business and serve you better. What should I do if I don't receive my item? If the products have problems how to do it? Don't leave any bad reviews firstly, that cannot solve any problem. Factory sales, best quality, and competitive price!

By the way, if you like our store, please add our store to your Favorite Stores, you can get our New arrival and Discount information in time. Due to the difference between different monitors, the picture may not reflect the actual color of the item. We guarantee the style is the same as shown in the pictures. Please allow slight dimension difference due to different manual measurements.

DEAR, ITS NORMAL THERE IS COLOR SHADING. If you encounter any problems, broken, quality problems, please don't worry, and don't leave bad feedback. We understand your mood, and will provide you with the best solution for your problem. Please give us the opportunity to solve the problem. In any case, please feel free to come to us, we are always here. Look forward to and thank you for your trust. These charges are the buyers responsibility. SIGN UP FOR ALL THE LATEST NEWS AND EXCLUSIVE OFFERS. NEW ARRIVALS NOW AVAILABLE AT DISCOUNTED PRICES. Tedexports was initially developed by us in our specializing in manufacturing high-end accessories and items.

We are a Sri Lanka and China-based company with locations in Colombo and Beijing County as well as our new location It is also set to launch in California in the near future. We develop all of our products in-house and work alongside leading retail suppliers.

Our products can be seen and bought through hundreds of accessories dealerships, both privately and corporate-owned. You can enjoy top-quality product and high-quality services from us, trust we that you will have a pleasant shopping experience here. We guaranty top quality with all of the products that we sell.

We strive to be number one in the industry and are willing to beat our competitor's pricing as well as exceeding industry standards with respect to quality. The item "SF-HC25G thc plasma cnc cutting machine automatic Arc cap voltage Plasma cutting" is in sale since Saturday, August 22, 2020. This item is in the category "Business & Industrial\CNC, Metalworking & Manufacturing\Welding & Soldering Equipment\Welding Equipment & Accessories\Welders, Cutters & Torches\Plasma Cutters". The seller is "tedexports" and is located in Beijing. This item can be shipped worldwide.
SF-HC25G thc plasma cnc cutting machine automatic Arc cap voltage Plasma cutting


Home  Sitemap  Contact Us  Privacy Policy  Service Agreement